What size nails for framing walls?

Use 16d common or sinker nails (3.5 inches) for face-nailing through plates into stud ends. Use 10d or 8d nails for toenailing studs to plates. For sheathing, use 8d nails. Most pneumatic framing nailers fire 3.1 to 3.5-inch nails in either stick (angled) or coil format.

How many nails per stud?

Each stud needs two 16d nails at each end (through the plate into the stud end), totaling 4 nails per stud minimum. Add 2 to 3 extra nails per stud for toenailing at corners, partition intersections, and header connections. A reasonable average is 6 to 8 nails per stud across an entire wall.

How many pounds of framing nails do I need for a house?

A typical 1,500 sq ft single-story house with 200 to 300 studs requires 40 to 60 pounds of framing nails for the wall framing alone. Including floor framing, roof framing, and sheathing, total nail usage is typically 100 to 150 pounds. Buy in 30-pound boxes or by the case for the best price.

Do I need galvanized nails for pressure-treated lumber?

Yes. The copper compounds in modern pressure-treated lumber (ACQ, CA-B) corrode standard bright and vinyl-coated nails. Use hot-dipped galvanized (HDG) or stainless steel nails for all connections involving PT lumber. This includes sill plates, PT bottom plates, and any exterior applications.

What nail gun angle should I buy for framing?

The most common framing nailer angles are 21-degree (full round head, preferred by many codes), 28-degree (wire-weld collation), and 30-degree (paper-tape collation, fits into tighter spaces). The 30-degree nailer is the most versatile for reaching into corners and tight spots. Check your local code — some jurisdictions require full round-head nails.

What is the IRC nailing schedule for framing?

The IRC Table R602.3(1) specifies the exact nail size, quantity, and type for each framing connection. Key requirements include: 2 nails per stud end through plates, 3 nails per rim joist to sill plate, stud-to-stud at corners requires 16d at 24 inches on center, and double top plates require 16d nails staggered at 16 inches. Always keep a copy of the nailing schedule on site for inspector review.

Kostenloser Rahmennägel-Rechner — kg & Kosten (2026)

Rahmennägel-Rechner: Wie viele Kilogramm Nägel für mein Projekt? Kostenloses Tool basierend auf Ständeranzahl.

Ad — 728x90 — Leaderboard

Geben Sie Ihre Maße ein

So verwenden Sie diesen Rechner

1Enter total number of studs in your project.
2Click Calculate.

Ad — 728x90 — Mid-Page

Über dieses Material

Framing nails are the primary fastener used to assemble wood-frame structures. The standard framing nail is the 16d (3.5-inch) sinker or common nail, used for face-nailing studs through plates and connecting structural members. Pneumatic framing nailers use stick (21-degree, 28-degree, or 30-degree) or coil nails ranging from 3.1 to 3.5 inches in length. Nail types include bright (uncoated), vinyl-coated (sinkers, for easier driving), hot-dipped galvanized (for exterior and PT lumber), and stainless steel (for coastal and corrosive environments). A 30-pound box of 16d sinkers contains approximately 500 nails. Hand-drive nails are available but rarely used in modern framing due to the speed advantage of pneumatic nailers. The IRC prescribes a specific nailing schedule for each framing connection — for example, two 16d nails per stud end through the plate, and three 16d nails per rim joist connection. Framing nails cost $40 to $60 per 30-pound box, or $30 to $50 per case of collated strip nails for pneumatic guns.

Nächste Schritte:

Stud Calculator →Joist Hanger Calculator →

Einbautipps

•End nail through plates into studs (2 nails per end).
•Toenail extra studs at corners and openings.
•Use 3" nails for stud-to-plate connections if shooting through an angle.

Häufige Fehler, die Sie vermeiden sollten

Under-nailing — always follow IRC nailing schedule for structural connections.
Using roofing nails for framing — wrong nail, wrong shank, wrong head.

Kostenloser Rahmennägel-Rechner — kg & Kosten (2026)

So verwenden Sie diesen Rechner

Über dieses Material

Einbautipps

Häufige Fehler, die Sie vermeiden sollten

Häufig gestellte Fragen

Verwandte Rechner

Kostenloser Balkenschuh-Rechner — Stück & Typ (2026)

Kostenloser Sturmklammer-Rechner — Stück & Kosten (2026)

Kostenloser Holzkosten-Rechner — Stück & Gesamt (2026)

Kostenloser Schnittholz-Rechner — BF & Kosten (2026)